Krishnan Balasubramanian

This paper reports the simultaneous generation of multiple fundamental ultrasonic guided wave modes L(0,1), T(0,1), and F(1,1) on a thin wire-like waveguide (SS-308L) and its interactions with liquid loading in different attenuation dispersion regimes. An application towards liquid level measurements using these dispersion effects was also demonstrated. The finite element method (FEM) was used to understand the mode behavior and their dispersion effects at different operating frequencies and subsequently validated with experiments. In addition, the ideal configuration for the simultaneous generation of at least two modes (L(0,1), T(0,1), or F(1,1)) is reported. These modes were transmitted/received simultaneously on the waveguide by an ultrasonic shear wave transducer aligned at 0◦/45◦/90◦ to the waveguide axis. Level measurement experiments were performed in deionized water and the flexural mode F(1,1) was observed to have distinct dispersion effects at various frequency ranges (i.e., >250 kHz, >500 kHz, and >1000 kHz). The shift in time of flight (TOF) and the central frequency of F(1,1) was continuously measured/monitored and their attenuation dispersion effects were correlated to the liquid level measurements at these three operating regimes. The behavior of ultrasonic guided wave mode F(1,1) when embedded with fluid at three distinct frequency ranges (i.e., >250 kHz, >500 kHz, and >1000 kHz) were studied and the use of low frequency Regime-I (250 kHz) for high range of liquid level measurements and the Regime-II (500 kHz) for low range of liquid level measurements using the F(1,1) mode with high sensitivity is reported.

Wall thickness reduction, which typically results from corrosion, erosion, or operating conditions, is a significant challenge in many industries. In order to generate a broadband pure shear horizontal wave mode in plate structures, this paper proposes a magnetostrictive patch transducer called the Staircase Magnetostrictive Patch (ScaMP) Transducer. For ScaMP transduction, an optimised patch width offers a broadband frequency response is employed. The lowest remnant thickness of the sample was estimated using the wideband SH1 dispersive guided wave mode's cut-off property. The broad frequency excitation method enabled measurement over a range of wall thinning up to 80% of the nominal thickness with a single data acquisition. Experiments were carried out on an 8 mm nominal wall thickness aluminium plate with gouge defects to evaluate the proposed sensor's broad frequency response. The measurement of remnant thickness was estimated with a maximum error of 5.5%.

Ultrasonic SHM approaches using bulk or guided waves has been well documented. Here the waves are generate using PZT transduction that requires excitation inputs using either high voltage or high current or both. Several critical applications such as component in explosion susceptible environment, extreme temperature condition, etc. have limitations in deployment of high voltage/current excitation. In this paper, the use of wave-guide-based excitation is explored for plate and pipe like geometries. The waveguide help isolate the excitation part of the ultrasound generation, away from the component that may be in a hostile condition. The ultrasound wave modes excited in the waveguide is coupled to the structure and optimized to generate the desired guided wave modes in the geometry of the structures using Finite Element Wave Propagation models. The reception of these modes are also explored using similar ultrasonic waveguides. The detection of defects, in an SHM mode, using this remote generation approach is also demonstrated on a plate geometry component. This article demonstrates the detection of fundamental symmetric wave mode (S0), shear horizontal waves (SH0) and antisymmetric wave mode (A0) in an steel plate by placing a thin wire-like stainless steel waveguide sensor. In order to uniquely identify the three-fundamental plate-guided modes, we map the experimentally measured group velocities as detected by the waveguide sensor to theoretically obtained group velocity dispersion curves. The analytically obtained FEM results are evaluated experimentally using time-of-flight measurements. In future, this sensor arrangement may be utilized in areas like high-temperature furnaces, engines and aircrafts for detecting cracks.

This work explores the generation of Lamb waves and their higher harmonics using a pattern source. An array of laser sources, when used with a short-pulsed laser, generate multiple Lamb modes in a plate-like component. The variation in duty ratio of the pattern source is found to influence the generation of fundamental modes and their harmonics. A two-dimensional finite element model is developed to simulate the narrowband Lamb wave generation process, and validated against targeted experiments. For a ‘square-like’ spatial profile of energy distribution, the second harmonic of the fundamental wave modes is fully suppressed at the duty ratio of 0.5, and the third harmonic of the fundamental wave modes is fully suppressed at duty ratios of 1/3 and 2/3. As the duty ratio increased from 0.2 to 0.8, the variation in amplitude of the fundamental modes is greater than that of the higher order modes. For duty ratio values less than 0.25 and greater than 0.75, the second harmonic component of the fundamental waves had approximately the same amplitude as the fundamental wave modes. Similarly, the third harmonic of the fundamental wave modes had the same amplitude or slightly higher amplitude than the higher order Lamb modes for duty ratio values less than 0.25 and greater than 0.75.