Raghunathan Rengasamy

The amount of current generated in a polymer electrolyte membrane fuel cell (PEMFC) depends strongly on the local conditions in a cathode such as available oxygen, surface area available for the reactions, amount of ionomer, and amount of electro-catalyst. In the present work, design parameters of a cathode catalyst layer are optimized to achieve the maximum current density at a given operating voltage. The decision variables are chosen such that they can be realized experimentally. To understand the effect of the model fidelity on the decision variables, optimization is performed with a single phase model and a two-phase model with and without membrane. Other objective functions such as maximization of current generation per catalyst loading, minimization of catalyst layer cost per power and minimization of cell cost per power are also considered to study the effects of the objective functions on the decision variables. © 2010 The Institution of Chemical Engineers.

A two-dimensional two-phase steady state model of the cathode of a polymer electrolyte membrane fuel cell (PEMFC) is developed using unsaturated flow theory (UFT). A gas flow field, a gas diffusion layer (GDL), a microporous layers (MPL), a finite catalyst layer (CL), and a polymer membrane constitute the model domain. The flow of liquid water in the cathode flow channel is assumed to take place in the form of a mist. The CL is modeled using flooded spherical agglomerate characterization. Liquid water is considered in all the porous layers. For liquid water transport in the membrane, electro-osmotic drag and back diffusion are considered to be the dominating mechanisms. The void fraction in the CL is expressed in terms of practically achievable design parameters such as platinum loading, Nafion loading, CL thickness, and fraction of platinum on carbon. A number of sensitivity studies are conducted with the developed model. The optimum operating temperature of the cell is found to be 80-85 °C. The optimum porosity of the GDL for this cell is in the range of 0.7-0.8. A study by varying the design parameters of the CL shows that the cell performs better with 0.3-0.35 mg cm-2 of platinum and 25-30 wt% of ionomer loading at high current densities. The sensitivity study shows that a multi-variable optimization study can significantly improve the cell performance. Numerical simulations are performed to study the dependence of capillary pressure on liquid saturation using various correlations. The impact of the interface saturation on the cell performance is studied. Under certain operating conditions and for certain combination of materials in the GDL and CL, it is found that the presence of a MPL can deteriorate the performance especially at high current density. © 2010 Elsevier B.V. All rights reserved.

The cathode catalyst layer (CL) of a PEM fuel cell (PEMFC) plays an important role in the performance of the cell because of the rate limiting mechanisms that take place in it. For enhancing the performance of a PEMFC, the use of multiple, ultra thin CLs instead of a single CL is considered in the present work. Since the concentration of oxygen decreases in a CL from the diffusion medium-CL interface towards the polymer membrane, the CL adjacent to the diffusion medium should be of higher porosity than the other CLs. Similarly, the CL adjacent to the polymer membrane should contain more ionomer than the other CLs. Furthermore, liquid water should be removed without causing significant mass transport and/or ohmic losses. Therefore, the design parameters of a CL can be varied spatially to minimize losses in a PEMFC. However, such a continuously graded CL is difficult to manufacture due to lack of commercially available techniques and associated costs. As an alternative, a combination of layers can be synthesized where each layer is manufactured with different design parameters. This approach provides the opportunity to optimize the design parameters of each layer. With this objective in mind, a detailed steady state model of a PEMFC cathode with multiple layers is developed. The model considers liquid water in all the layers. The catalyst layer microstructure is modeled as a network of spherical agglomerates. For improved water management, a thin micro-porous layer is considered between the gas diffusion layer (GDL) and the first catalyst layer. The performance curves for various combinations of the design parameters are shown and the results are analyzed. The results show that there exists an optimum combination of design parameters for each catalyst layer that can significantly improve the performance of a PEMFC. © 2010 Professor T. Nejat Veziroglu. Published by Elsevier Ltd. All rights reserved.

The cathode catalyst layer (CL) of a PEM fuel cell (PEMFC) plays an important role in the performance of the cell because of the rate limiting mechanisms that take place in it. For enhancing the performance of a PEMFC, the use of multiple, ultra thin CLs instead of a single CL is considered in the present work. Since the concentration of oxygen decreases in a CL from the diffusion medium-CL interface towards the polymer membrane, the CL adjacent to the diffusion medium should be of higher porosity than the other CLs. Similarly, the CL adjacent to the polymer membrane should contain more ionomer than the other CLs. Furthermore, liquid water should be removed without causing significant mass transport and/or ohmic losses. Therefore, the design parameters of a CL can be varied spatially to minimize losses in a PEMFC. However, such a continuously graded CL is difficult to manufacture due to lack of commercially available techniques and associated costs. As an alternative, a combination of layers can be synthesized where each layer is manufactured with different design parameters. This approach provides the opportunity to optimize the design parameters of each layer. With this objective in mind, a detailed steady state model of a PEMFC cathode with multiple layers is developed. The model considers liquid water in all the layers. The catalyst layer microstructure is modeled as a network of spherical agglomerates. For improved water management, a thin micro-porous layer is considered between the gas diffusion layer (GDL) and the first catalyst layer. The performance curves for various combinations of the design parameters are shown and the results are analyzed. The results show that there exists an optimum combination of design parameters for each catalyst layer that can significantly improve the performance of a PEMFC.